AX Section
Gates Tri-Power® AX Section
Notched Vee Belts
| Belt Numbers | Outside Length | Top Width | Belt Numbers | Outside Length | Top Width |
| AX20 | 558 mm [22"] | 13 mm | AX53 | 1397 mm [55"] | 13 mm |
| AX21 | 585 mm [23"] | 13 mm | AX54 | 1422 mm [56"] | 13 mm |
| AX22 | 610 mm [24"] | 13 mm | AX55 | 1447 mm [57"] | 13 mm |
| AX23 | 635 mm [25"] | 13 mm | AX56 | 1473 mm [58"] | 13 mm |
| AX24 | 660 mm [26"] | 13 mm | AX58 | 1525 mm [60"] | 13 mm |
| AX25 | 685 mm [27"] | 13 mm | AX60 | 1575 mm [62"] | 13 mm |
| AX26 | 710 mm [28"] | 13 mm | AX62 | 1625 mm [64"] | 13 mm |
| AX27 | 735 mm [29"] | 13 mm | AX64 | 1675 mm [66"] | 13 mm |
| AX28 | 760 mm [30"] | 13 mm | AX66 | 1727 mm [68"] | 13 mm |
| AX29 | 785 mm [31"] | 13 mm | AX68 | 1777 mm [70"] | 13 mm |
| AX30 | 815 mm [32"] | 13 mm | AX70 | 1830 mm [72"] | 13 mm |
| AX31 | 838 mm [33"] | 13 mm | AX71 | 1855 mm [73"] | 13 mm |
| AX32 | 865 mm [34"] | 13 mm | AX75 | 1955 mm [77"] | 13 mm |
| AX33 | 890 mm [35"] | 13 mm | AX78 | 2032 mm [80"] | 13 mm |
| AX34 | 915 mm [36"] | 13 mm | AX80 | 2083 mm [82"] | 13 mm |
| AX35 | 940 mm [37"] | 13 mm | AX85 | 2210 mm [87"] | 13 mm |
| AX36 | 965 mm [38"] | 13 mm | AX90 | 2337 mm [92"] | 13 mm |
| AX37 | 990 mm [39"] | 13 mm | AX96 | 2490 mm [98"] | 13 mm |
| AX38 | 1015 mm [40"] | 13 mm | AX103 | 2667 mm [105"] | 13 mm |
| AX39 | 1040 mm [41"] | 13 mm | AX105 | 2717 mm [107"] | 13 mm |
| AX41 | 1092 mm [43"] | 13 mm | AX110 | 2845 mm [112"] | 13 mm |
| AX42 | 1120 mm [44"] | 13 mm | AX112 | 2895 mm [114"] | 13 mm |
| AX43 | 1143 mm [45"] | 13 mm | AX120 | 3100 mm [122"] | 13 mm |
| AX44 | 1168 mm [46"] | 13 mm | AX128 | 3300 mm [130"] | 13 mm |
| AX46 | 1220 mm [48"] | 13 mm | AX144 | 3710 mm [146"] | 13 mm |
| AX48 | 1270 mm [50"] | 13 mm | AX173 | 4445 mm [175"] | 13 mm |
| AX51 | 1345 mm [53"] | 13 mm | |||
Gates Tri-Power V-Belts are built for superior performance on heavy duty drives of classical cross section.
The Raw Edge construction and special notched tooth design makes the Tri Power belt especially suited for drives requiring small diameter pulleys and flat backside idlers.
Construction
- Raw Edge construction.
- Classical cross section.
- Molded notches reduce and evenly distribute thermal and bending stresses.
- The molded notch tooth pattern reduces noise.
- Precision ground sidewalls give uniform wedging action.
- Flat, back side idlers can be used. Recommended 110mm minimum diameter.
- Inside pulleys and idlers recommended minimum 60mm Ø.
- Tri-Power belts will not catch fire from heat or heat build up, even with severe slippage.
- Static conductive- ISO 1813 and RMA IP 3-3
Advantages
- Excellent performance/cost ratio.
- Reliability and efficency.
- Long belt life reduces replacement and maintenance costs.
- All sizes meet Gates V80 matching requirements.
Scroll down for further information
↓
