×

BX Section

Gates Tri-Power® BX Section Vee Belts

 

Belt Numbers Outside Length Top Width Belt Numbers Outside Length Top Width
           
BX25  711 mm  [28"]  17 mm  BX49  1320.8 mm  [52"]  17 mm
BX26  736.6 mm  [29"]  17 mm  BX50  1346 mm  [53"]  17 mm
BX27 762 mm  [30"]  17 mm  BX51  1371.6 mm  [54"]  17 mm
BX28  787.4 mm  [31"]  17 mm  BX52  1397 mm  [55"]  17 mm
BX29  812.8 mm  [32"]  17 mm  BX53  1422.4 mm  [56"]  17 mm 
BX30  838 mm  [33"]  17 mm  BX54  1447.8 mm  [57"]  17 mm 
BX31  863.6 mm  [34"]  17 mm  BX55  1473 mm  [58"]  17 mm 
BX32  889 mm  [35"]  17 mm  BX59  1574.8 mm  [62"]  17 mm 
BX36  990.6 mm  [39"]  17 mm  BX60  1600 mm  [63"]  17 mm 
BX37  1016 mm  [40"]  17 mm  BX61  1625.6 mm  [64"]  17 mm 
BX38  1041 mm  [41"]  17 mm  BX63  1676.4 mm  [66"]  17 mm 
BX40  1092 mm  [43"]  17 mm BX64  1701.8 mm  [67"]  17 mm 
BX41  1117.6 mm  [44"]  17 mm  BX65  1727 mm  [68"]  17 mm 
BX42  1143 mm  [45"]  17 mm  BX68  1803.4 mm  [71"]  17 mm 
BX43  1168.4 mm  [46"]  17 mm  BX71  1879.6 mm  [74"]  17 mm 
BX44  1193.8 mm  [47"]  17 mm  BX75  1981 mm  [78"]  17 mm 
BX46  1244.6 mm  [49"]  17 mm  BX76  2006.6 mm  [79"]  17 mm 
BX47 1270 mm  [50"]  17 mm  BX85  2235 mm  [88"]  17 mm 
BX48  1295.4 mm  [51"]  17 mm  BX90  2362 mm  [93"]  17 mm 
           
           

 

Gates Tri-Power V-Belts are built for superior performance on heavy duty drives of classical cross section.

The raw edge construction and special notch design makes the Tri-Power belt especially suited for drives requiring small diameter pulleys and use of backside idlers. 

 

Construction

  • Raw edged construction.
  • Classical cross section.
  • Molded notches reduce and evenly distribute thermal and bending stresses.
  • Molded notch pattern reduces noise.
  • Precision ground sidewalls give a uniform wedging action.
  • Backside idlers can be used.
  • Flex bonded tensile cords are vulcanized as one unit, increasing the belts resistance to tensile and flexing forces, fatigue and shock loads.
  • Elastomeric compound protects the belt against heat, ozone and sunlight.
  • The belt will not catch fire from heat build up, even under severe slippage.
  • Static conductive- ISO 1813 and RMA IP3-3

 

Advantages

  • Excellent performance/cost ratio.
  • Reliability and efficiency.
  • Long belt life reduces replacement and maintenance costs.
  • All sizes meet the Gates V80 matching tolerances.
  • Minimum inside pulley sizes of 80mmØ
  • Minimum outside flat idlers of 60mmØ

 

 

 

 Scroll down for further information

View as Grid List

34 Items

Set Descending Direction
per page
View as Grid List

34 Items

Set Descending Direction
per page